Winch Accessories

WINCH SOLENOID 12V HEAVY DUTY UPGRADE ALBRIGHT EQUIV

AU $85.00

Waterproof 12V Winch Solenoid Heavy Duty Upgrade.

Spade Terminal Side Connections.

Features

• Heavy-duty one-piece waterproof winch solenoid for 12v electric winches up to 20,000lb.
• This model has the spade terminal connections on the side.
• Latest heavy-duty model larger contact faces/faster contact closure.
• Improve safety and reliability by upgrading from the 'twin can' solenoids found on many budget winches.
• Fully waterproof IP67 sealed case.
• Heavy-duty M8 primary connection posts.
• Mounting bracket pre-fitted for easy installation into your control box.
• Compatible with all WINCHMAX wireless remote systems.
• Wiring diagram supplied for winches with or without wireless control.

TWIN WIRELESS 12 VOLT WINCH REMOTE CONTROLS

AU $85.00

WINCHMAX Twin Wireless Winch Remote Control Kit Handset 12v

Features

• Operating Range over 30m (100ft)
• Supplied with two handheld controllers.
• Sealed rubber buttons.
• Press and hold both buttons to power on/off
• Auto shut off after 5 minutes without use to preserve battery life
• Free- Fitted Battery in the remote.
• Heat shielded cables with pre-fitted heat shrink insulated terminals.
• Compact receiver is just 60mm x 45mm x 22mm so will fit safely inside most control box enclosures.
• Easy to fit, full installation instructions supplied.

TWIN WIRELESS 24 VOLT WINCH REMOTE CONTROLS

AU $85.00

WINCHMAX Twin Wireless Winch Remote Control Kit Handset 24v

Features

• Operating Range over 30m (100ft)
• Supplied with two handheld controllers.
• Sealed rubber buttons.
• Press and hold both buttons to power on/off
• Auto shut off after 5 minutes without use to preserve battery life
• Free- Fitted Battery in the remote.
• Heat shielded cables with pre-fitted heat shrink insulated terminals.
• Compact receiver is just 60mm x 45mm x 22mm so will fit safely inside most control box enclosures.
• Easy to fit, full installation instructions supplied.

8 TONNE SNATCH BLOCK / PULLEY FOR 4X4 OR RECOVERY WINCH

AU $50.00

• 260mm x 130mm x 65mm diameter hole.  For use with up to 14.5mm cable diameter.
• Weighing in at over 3KG this is a seriously heavy-duty product.
• Superb quality with grease nipple fitted on spindle
• Swing out plates pivot at pulley shaft for easy engagement / disengagement from winch cable
• Using a snatch block will double the pulling power of your winch or looking at it another way, it will half the strain, reducing current draw and loading on your winch motor, bearings and gearbox.

30M X 11.5MM DYNEEMA WINCH ROPE, HOOK & HAWSE

AU $399.00

DYNEEMA WINCH ROPE 

 30m x 10.5mm genuine Dyneema SK75 rope

• Ideal for 4×4 or recovery use.
• Thimble eye for clevis hook or shackle attachment
• Competition hook with safety catch and hand saver, black.
• M8 ring terminal attachment at the drum end to suit most standard winch drums.
• 3m protective sheave can be used at drum end for in drum brake systems or at the hook end to provide extra abrasion protection.
• Minimum breaking load 7,720kg (17,020lb).
• Significant safety benefits compared to steel wire rope.
• 8x Lighter than steel wire rope.
• Does not kink.
• No wire splinters.
• Floats on water. 
• Can be handled without gloves.  

WINCH MOUNTING PLATE NUMBER 2

AU $99.00

Winch Mounting Plate for 13,500lb WINCHMAX Winches

For quick and easy installation of a winch on your recovery truck, recovery trailer, or other flatbed applications.

Also suitable for floor mount applications or as a basis for fabricating a custom 4x4 mounting plate.

Features

• Heavy-duty mounting plate (6mm steel) made especially to suit WINCHMAX brand winches up to 13,500lb or any other low-profile winch adhering to with a standard 254mm x 114.3mm (10" x 4.5") bolt pattern.
• Black powder-coated for excellent corrosion resistance.
• Pre-drilled for winch and roller fairlead.
• For other winches, you may need to use alternative fixings.
• Dimensions 930mm x 200mm x 110mm (LWH) 
• 5mm Thick

WINCH CABLE STEEL 24M X 9.5MM

AU $149.00

• 9.5mm Replacement Steel Winch Cable - With Hook

• Galvanized Cable With Drum Terminal and Loop Fitted With Thimble Eye

• Suitable for winches up to 13500lb

• 9.5mm x 26m Length

WINCH SOLENOID 24V HEAVY DUTY UPGRADE ALBRIGHT EQUIV

AU $85.00

Waterproof 24V Winch Solenoid Heavy Duty Upgrade.

Spade Terminal Side Connections.

Features

• Heavy-duty one-piece waterproof winch solenoid for 24v electric winches up to 20,000lb.
• This model has the spade terminal connections on the side.
• Latest heavy-duty model larger contact faces/faster contact closure.
• Improve safety and reliability by upgrading from the 'twin can' solenoids found on many budget winches.
• Fully waterproof IP67 sealed case.
• Heavy-duty M8 primary connection posts.
• Mounting bracket pre-fitted for easy installation into your control box.
• Compatible with all WINCHMAX wireless remote systems.
• Wiring diagram supplied for winches with or without wireless control.

WINCH MOUNTING PLATE NO 3

AU $99.00

Winch Mounting Plate for WINCHMAX Hydraulic and 17,000lb Electric Winches

For quick and easy installation of a winch on your recovery truck, recovery trailer, or other flatbed applications.

Also suitable for floor mount applications or as a basis for fabricating a custom 4x4 mounting plate.

Features

• Deeper (front to back) than our standard mounting plate to accommodate winches with larger diameter body such as the WINCHMAX range of hydraulic winches and the 17,000lb & 17,500lb electric models.
• Drilled for standard 254mm x 114.3mm (10" x 4.5") bolt pattern.
• Black powder-coated for excellent corrosion resistance.
• Pre-drilled for winch and roller fairlead
• Dimensions 550mm x 240mm x 90mm (LWH)
• 5mm Thick

ROLLER FAIRLEAD NO MORE RUSTY ROLLERS

AU $145.00

Heavy Duty Four Roller Fairlead Suitable For Winches Rated Up To 17000LB.

Features

• Overall Size W306mm x H106mm.
• Orange powder-coated frame finish.
• New low profile (45mm projection) design.
• Stainless steel rollers.
• Pre-drilled for standard two-hole mounting.
• Roller axels are secured with Nyloc nuts to allow roller removal.
• Recommended Mounting Bolt Size = M12

WINCH HOOK

AU $49.00

HEAVY DUTY WINCH HOOK 

16CM LENGTH

WINCH CONTROL BOX 24V

AU $249.00

   Complete 24V Electric Winch Control Box

 Wander Lead & Twin Wireless Remote Control

For 24V electric winches up to 7.0hp / 20000 lbs Complete system.

Features

• Latest technology long-range wireless remote controls, twin handsets
• Big grip wander lead with extra-long 4.5m cord.
• Suitable for all four terminal winch motors (i.e. three-terminal plus earth post) up to 7.0hp
• As used on WINCHMAX winches tried and tested in the harshest conditions so you can be confident of super reliability.
• Heavy-duty one-piece solenoid, latest design, ultra-reliable, IP67 waterproof.
• Tough ABS two-part case.

WINCHMAX LANDROVER DEFENDER WINCH BAR LED

AU $629.00

LAND ROVER DEFENDER WINCH BUMPER 

WITH LED 2 X SHACKLES - FITS WITH OR WITHOUT AIR CON

Suitable for all standard production Defenders (with or without aircon)

FEATURES

· This is a recreation of the original Land Rover part VPLDP0105 - (5mm thick steel).

· Very nice quality laser cut & powder coated in graphite black.

· Pre-drilled (114mm x 254mm) to take most standard pattern winches.

·  DLR - DC 9-30V.

·  Drilled to allow original bumper end caps to be transferred to winch bumper if required.

·  Designed to fit - up to 13,500lb electric winches only - please check the dimensions!

·  Not compatible with soft a bar.

FREIGHT 

As an oversized item, delivery to commercial address or Depot pick up

WINCHMAX MOUNTING PLATE 2 COMPACT

AU $99.00

Winch Mounting Plate 2 Compact 

For quick and easy installation of a winch on your recovery truck, recovery trailer, or other flatbed applications.

Also suitable for floor mount applications or as a basis for fabricating a custom 4x4 mounting plate.

Features

• Heavy-duty mounting plate made especially to suit WINCHMAX brand winches up to 13500lb or any other low profile winch adhering to with a standard 254mm x 114.3mm (10" x 4.5") bolt pattern.
• Dimensions- 580mm x 180mm x 100mm (LWH)
• 5mm Thick
• Black powder-coated for excellent corrosion resistance.
• Pre-drilled for winch and roller fairlead.

WINCHMAX LANDROVER DEFENDER WINCH BAR

AU $599.00

LAND ROVER DEFENDER WINCH BUMPER - FITS WITH OR WITHOUT AIR CON

Suitable for all standard production Defenders (with or without aircon)

FEATURES

• This is a recreation of the original Land Rover part VPLDP0105 - (5mm thick steel).
• Very nice heavy quality laser cut & powder coated in graphite black.
• Pre-drilled (114mm x 254mm) to take most standard pattern winches.
• Drilled to allow original bumper end caps to be transferred to the winch bumper if required.
• Designed to fit - up to 13,500lb electric winches only - please check dimensions!
• Compatible With - Land Rover Defender Soft A-Bar (as long as it's the winch version part number - VPLPP0061).

FREIGHT

 TO COMMERCIAL ADDRESS OR DEPOT PICK UP AS AN OVERSIZED ITEM.

WINCH BRAKE MODULE FOR 17000LB AND 20000LB WINCHMAX MODELS

AU $89.00

 Winch Brake Module

Suitable for 17000lb, 17500lb and 20000lb Winches

• These are third-generation designs and it is essential that the customer checks against their existing part for compatibility.